YachtDatabase.com

Review of Morris 28 Linda


Basic specs.

sail specifications
The Morris 28 Linda is a sailboat designed by the maritime architect Chuck W. Paine in the mid eighties. Only a few boats have been produced. The Morris 28 Linda is built by the American yard Morris Yachts.

Here we would have liked to show you nice photos of the Morris 28 Linda.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Morris 28 Linda or similar boat for sale

Hull
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Rig
The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Engine

The boat is typically equipped with a Volvo Penta diesel engine.

The fuel tank has a capacity of 68 liters (17 US gallons, 14 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Morris 28 Linda is 1.81, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.5 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Morris 28 Linda is about 133 kg/cm, alternatively 746 lbs/inch.
Meaning: if you load 133 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 746 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Morris 28 Linda is 26.9.

Low High 79% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 79% of all similar sailboat designs. This is a comfort value significantly above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Morris 28 Linda is 3.05.

Slim Wide 50% 0 50 100
Compared with other similar sailboats it is more spacy than 50% of all other designs. It seems that the designer has chosen an average hull design.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Morris 28 Linda is 291 which categorizes this boat among 'medium weight cruisers'.

Heavy Light 31% 0 50 100
31% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Morris 28 Linda with ISO 8666 reference sail is 14.8, with a 135% genua the SA/D is 17.1.

Low High 34% 0 50 100
The SA/D ratio indicates that it is faster than 34% of all similar sailboat designs in light wind.


Maintenance

Rig

Dimensions of sail for masthead rig.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 29.9 m(98.0 feet)8 mm(5/16 inch)
Jib/genoa halyard29.9 m(98.0 feet)8 mm(5/16 inch)
Spinnaker halyard29.9 m(98.0 feet)8 mm(5/16 inch)
Jib sheet 8.5 m(28.0 feet)10 mm(3/8 inch)
Genoa sheet8.5 m(28.0 feet)10 mm(3/8 inch)
Mainsheet 21.3 m(70.0 feet)10 mm(3/8 inch)
Spinnaker sheet18.8 m(61.6 feet)10 mm(3/8 inch)
Cunningham3.4 m(11.2 feet)8 mm(5/16 inch)
Kickingstrap6.8 m(22.3 feet)8 mm(5/16 inch)
Clew-outhaul6.8 m(22.3 feet)8 mm(5/16 inch)

Boat owner's ideas

This section is reserved boat owner's changes, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Morris 28 Linda it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References