Review of Excalibur 36

Excalibur 36.

Basic specs.

The Excalibur 36 is a sailboat designed by the Dutch maritime architect Ericus Gerhardus van de Stadt in the early sixties. Less than 100 boats have been built. The Excalibur 36 is built by the British yard Tyler Boat Company Ltd..

Winning the RORC Class II Championships in 1963, 1964 and 1965. Moulded by the Tyler Boat Co

Looking for a new boat? Find an Excalibur 36 or similar boat for sale

Hull

Both the hull and the deck is made of fibreglass. A hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Interior

The boat is equipped with one cabin, 2+3 berths, a galley and toilet facility.

Rig

The Excalibur 36 is built with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Keel

Fin keel

The Excalibur 36 is built with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can only enter major marinas as the draft is about 1.81 - 1.91 meter (5.94 - 6.24 ft) dependent on the load. See immersion rate below.

Engine

Excalibur 36 may be equipped with an inboard Yanmar 2QM15 diesel engine at 15 hp (11 kW). Calculated max speed is about 3.8 knots

The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Excalibur 36 is 1.61, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.8 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Excalibur 36 is about 161 kg/cm, alternatively 904 lbs/inch.
Meaning: if you load 161 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 904 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Excalibur 36 is 33.4 - 37.4.

Comparing this ratio with similar sailboats show that it is more comfortable than 93% of all similar sailboat designs. This is a comfort value significantly above average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Excalibur 36 is 3.61.

Compared with other similar sailboats it is slimmer than 88% of all other designs. It seems that the designer has chosen a significantly more speedy hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Excalibur 36 is 41%.

This ballast ratio is higher than 58% of all similar sailboat designs. Since the ballast ratio and the righting moment (i.e. better ability to resist heeling) is strongly correlated, a ballast ratio just above average indicates an ability to resist heeling above average.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Excalibur 36 is 363 which categorizes this boat among 'ultra heavy cruisers'.

15% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.

SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 15.96

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 29m² (312 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Jib sheet	11.0 m	(36.0 feet)	14 mm	(0.55 inch)
Genoa sheet	11.0 m	(36.0 feet)	14 mm	(0.55 inch)
Mainsheet	27.4 m	(90.0 feet)	14 mm	(0.55 inch)
Spinnaker sheet	24.1 m	(79.2 feet)	14 mm	(0.55 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Excalibur 36 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.