Review of Allied Seabreeze 35

Basic specs.

sail specifications
The Allied Seabreeze 35 is a sailboat designed in the mid sixties.

Here we would have liked to show you nice photos of the Allied Seabreeze 35.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Allied Seabreeze 35 or similar boat for sale


The Allied Seabreeze 35 is equipped with a centerboard keel. A centerboard keel is a pivoting lifting keel, allowing to sail both coastal and inland waters.

The boat can enter even shallow marinas as the draft is just about 1.16 - 1.26 meter (3.81 - 4.11 ft) dependent on the load. See immersion rate below.


The boat is typically equipped with an engine.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.6 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Allied Seabreeze 35 is about 153 kg/cm, alternatively 862 lbs/inch.
Meaning: if you load 153 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 862 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Allied Seabreeze 35 is 3.40.

Wide Slim 69% 0 50 100
Compared with other similar sailboats it is slimmer than 69% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.

Over- / underrigged

Low High 21% 0 50 100
The Allied Seabreeze 35 has more rig than 21% of all similar sailboats, which indicates that the boat is significantly underrigged.


Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 29m2 (312 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Dimensions of sail.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

Guiding dimensions of running rig
Mainsail halyard 27.9 m(91.5 feet)12 mm(1/2 inch)
Jib/genoa halyard27.9 m(91.5 feet)12 mm(1/2 inch)
Spinnaker halyard27.9 m(91.5 feet)12 mm(1/2 inch)
Jib sheet 10.7 m(35.0 feet)14 mm(0.55 inch)
Genoa sheet10.7 m(35.0 feet)14 mm(0.55 inch)
Mainsheet 26.7 m(87.5 feet)14 mm(0.55 inch)
Spinnaker sheet23.5 m(77.0 feet)14 mm(0.55 inch)
Cunningham4.8 m(15.8 feet)12 mm(1/2 inch)
Kickingstrap9.6 m(31.6 feet)12 mm(1/2 inch)
Clew-outhaul9.6 m(31.6 feet)12 mm(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.


We are always looking for new photos. If you can contribute with photos for Allied Seabreeze 35 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.