Review of Mamba 35

Basic specs.

The Mamba 35 is a sailboat designed by the Swedish maritime architect Harry Becker in the early eighties.

Here we would have liked to show you nice photos of the Mamba 35.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Mamba 35 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Rig

The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Mamba 35 is 1.80, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.2 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Mamba 35 is about 184 kg/cm, alternatively 1035 lbs/inch.
Meaning: if you load 184 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1035 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Mamba 35 is 25.7.

Comparing this ratio with similar sailboats show that it is more comfortable than 42% of all similar sailboat designs. This comfort value is just below average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Mamba 35 is 3.50.

Compared with other similar sailboats it is slimmer than 82% of all other designs. It seems that the designer has chosen a significantly more speedy hull design.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Mamba 35 is 205 which categorizes this boat among 'light crusers & offshore racers'.

73% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.

SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Mamba 35 with ISO 8666 reference sail is 17.8, with a 135% genua the SA/D is 20.6.

The SA/D ratio indicates that it is faster than 66% of all similar sailboat designs in light wind.

RSP (Relative Speed Performance)

What is Relative Speed Performance?

The Relative Speed Performance for Mamba 35 is 66

The relative speed performance is 66 which means that a it is faster than 66% of all similar sailboat designs.

Maintenance

Rig

Dimensions of sail for fractional rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	37.5 m	(123.2 feet)	12 mm	(1/2 inch)
Jib/genoa halyard	37.5 m	(123.2 feet)	12 mm	(1/2 inch)
Spinnaker halyard	37.5 m	(123.2 feet)	12 mm	(1/2 inch)
Jib sheet	10.8 m	(35.6 feet)	14 mm	(0.55 inch)
Genoa sheet	10.8 m	(35.6 feet)	14 mm	(0.55 inch)
Mainsheet	27.1 m	(89.0 feet)	14 mm	(0.55 inch)
Spinnaker sheet	23.9 m	(78.3 feet)	14 mm	(0.55 inch)
Cunningham	4.0 m	(13.1 feet)	12 mm	(1/2 inch)
Kickingstrap	8.0 m	(26.2 feet)	12 mm	(1/2 inch)
Clew-outhaul	8.0 m	(26.2 feet)	12 mm	(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's changes, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Mamba 35 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.