The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The Mariner 40 (Garden) is equipped with a ketch rig. A ketch rig is generally considered easier to handle, because the sails are smaller, and because it can sail on most points to the wind with one sail completely taken down for repair or while reefing. The sail configuration of a ketch allows for better comfort and stability when sailing downwind or on a broad reach.
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Mariner 40 (Garden) is 1.53, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 7.4 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Mariner 40 (Garden) is about 214 kg/cm, alternatively 1201 lbs/inch.
Meaning: if you load 214 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1201 lbs cargo on the boat it will sink 1 inch.
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is L/B (Length Beam Ratio)?
The l/b ratio for Mariner 40 (Garden) is 3.53.
What is Displacement Length Ratio?
The DL-ratio for Mariner 40 (Garden) is 430 which categorizes this boat among 'heavy cruisers'.
What is SA/D (Sail Area Displacement ratio)?
The SA/D for Mariner 40 (Garden) with ISO 8666 reference sail is 12.5, with a 135% genua the SA/D is 14.9.
Dimensions of sail for ketch rig.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
Usage | Length | Diameter | ||
Mainsail halyard | 33.1 m | (108.7 feet) | 12 mm | (1/2 inch) |
Jib/genoa halyard | 33.1 m | (108.7 feet) | 12 mm | (1/2 inch) |
Spinnaker halyard | 33.1 m | (108.7 feet) | 12 mm | (1/2 inch) |
Jib sheet | 12.3 m | (40.3 feet) | 14 mm | (0.55 inch) |
Genoa sheet | 12.3 m | (40.3 feet) | 14 mm | (0.55 inch) |
Mainsheet | 30.7 m | (100.8 feet) | 14 mm | (0.55 inch) |
Spinnaker sheet | 27.0 m | (88.7 feet) | 14 mm | (0.55 inch) |
Cunningham | 4.7 m | (15.3 feet) | 12 mm | (1/2 inch) |
Kickingstrap | 9.3 m | (30.5 feet) | 12 mm | (1/2 inch) |
Clew-outhaul | 9.3 m | (30.5 feet) | 12 mm | (1/2 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Mariner 40 (Garden) it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.