Review of Sprinto

The Sprinto has been built with different keel alternatives.

Unknown keel type

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can sail close to the beach as the draft is just 0.20 - 0.30 meter (0.66 - 0.96 ft) dependent of the load. See immersion rate below.

Unknown keel type

This keel is also made of lead.

The boat can enter even shallow marinas as the draft is just about 1.45 - 1.55 meter (4.76 - 5.06 ft) dependent on the load. See immersion rate below.

Unknown keel type

Sprinto can enter even shallow marinas as the draft is just about 0.78 - 0.88 meter (2.56 - 2.86 ft) dependent on the load. See immersion rate below.

Fin keel with bulb

The Sprinto is built with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel. The advantage of the bulb is that it lowers the center of gravity which increases the righting moment and reduces the draft.

What is Capsize Screening Formula (CSF)?

The capsize screening value for Sprinto is 2.60, indicating that this boat would not be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.2 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Sprinto is about 100 kg/cm, alternatively 562 lbs/inch.
Meaning: if you load 100 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 562 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Sprinto is 7.5.

Comparing this ratio with similar sailboats show that it is more comfortable than 10% of all similar sailboat designs. This is a comfort value significantly below average.

What is L/B (Length Beam Ratio)?

The l/b ratio for Sprinto is 2.88.

Compared with other similar sailboats it is slimmer than 58% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.

What is a Ballast Ratio?

The ballast ratio for Sprinto is 39%.

This ballast ratio is higher than 54% of all similar sailboat designs. Since the ballast ratio and the righting moment (i.e. better ability to resist heeling) is strongly correlated, a ballast ratio just above average indicates an ability to resist heeling above average.

What is Displacement Length Ratio?

The DL-ratio for Sprinto is 69 which categorizes this boat among 'ultra light racers'.

92% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 19m² (204 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

Keels with moving parts need to be inspected and maintained on a regular basis according to advice given in owner's manual. Manufacturers usually advise which maintenance work can be done by the owner and which work should be carried out by a suitably experienced boatyard.

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

We are always looking for new photos. If you can contribute with photos for Sprinto it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.