Review of Sunbeam 39.2

Basic specs.

The Sunbeam 39.2 is a large sailboat designed by the Austrian maritime architect Manfred Schöchl. The Sunbeam 39.2 is built by the Austrian yard Schöchl Yachtbau GmbH.

Here we would have liked to show you nice photos of the Sunbeam 39.2.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Sunbeam 39.2 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Interior

The boat is equipped with 4+2 berths.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Sunbeam 39.2 is 1.21, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 8.4 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Sunbeam 39.2 is about 200 kg/cm, alternatively 1120 lbs/inch.
Meaning: if you load 200 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1120 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Sunbeam 39.2 is 46.7.

Comparing this ratio with similar sailboats show that it is more comfortable than 99% of all similar sailboat designs. This is a comfort value significantly above average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Sunbeam 39.2 is 4.92.

Compared with other similar sailboats it is slimmer than 100% of all other designs. It seems that the designer has chosen a significantly more speedy hull design. This type of design is also referred to as 'needle'.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Sunbeam 39.2 is 146 which categorizes this boat among 'ultra light racers'.

88% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.

Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Jib sheet	12.3 m	(40.4 feet)	14 mm	(0.55 inch)
Genoa sheet	12.3 m	(40.4 feet)	14 mm	(0.55 inch)
Mainsheet	30.8 m	(100.9 feet)	14 mm	(0.55 inch)
Spinnaker sheet	27.1 m	(88.8 feet)	14 mm	(0.55 inch)

Boat owner's ideas

This section is reserved boat owner's changes, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Sunbeam 39.2 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.