Review of Arcona 38

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.

The interior is like many other boats made of mahogany.
The boat is equipped with 3 cabins, 9 berths, a galley, toilet facility and 55 liter waste water capacity.

The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

The Arcona 38 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The boat can only enter major marinas as the draft is about 1.90 - 2.00 meter (6.23 - 6.53 ft) dependent on the load. See immersion rate below.

Arcona 38 is typically equipped with an inboard Volvo Penta MD2030 diesel engine at 28.0 hp (20 kW), which gives a max speed about 5.6 knots.

The transmission is a saildrive.

The fuel tank has a capacity of 90 liters (23 US gallons, 19 imperial gallons).

What is Capsize Screening Formula (CSF)?

The capsize screening value for Arcona 38 is 1.84, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.6 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Arcona 38 is about 227 kg/cm, alternatively 1273 lbs/inch.
Meaning: if you load 227 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1273 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Arcona 38 is 27.7.

Comparing this ratio with similar sailboats show that it is more comfortable than 46% of all similar sailboat designs. This comfort value is just below average.

What is L/B (Length Beam Ratio)?

The l/b ratio for Arcona 38 is 3.27.

Compared with other similar sailboats it is slimmer than 54% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.

What is a Ballast Ratio?

The ballast ratio for Arcona 38 is 35%.

This ballast ratio shows a righting moment that is higher than 27% of all similar sailboat designs. A righting moment (ability to resist heeling) just below average.

What is Displacement Length Ratio?

The DL-ratio for Arcona 38 is 216 which categorizes this boat among 'light crusers & offshore racers'.

66% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 39m² (419 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section is reserved boat owner's changes, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

We are always looking for new photos. If you can contribute with photos for Arcona 38 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.