Review of Oceanis 36 CC

Basic specs.

The Oceanis 36 CC aka Beneteau Oceanis 36 CC is a sailboat designed by the French maritime architect Jean Berret together with Olivier Racoupeau also from France in the mid nineties. The Oceanis 36 CC is built by the French yard Bénéteau.

Here we would have liked to show you nice photos of the Oceanis 36 CC.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Oceanis 36 CC or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Interior

The boat is equipped with 6 berths.

Rig

The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Engine

The boat is typically equipped with an engine.

The transmission is a shaft drive. A shaft drive will in the long run require less maintenence than other types of drive e.g. a sail drive.

The fuel tank has a capacity of 150 liters (39 US gallons, 32 imperial gallons).

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

EU classification

Oceanis 36 CC holds one CE certification:

The boat is by European Union certified as Class A. OCEAN:

Designed for extended voyages where conditions may exceed wind force 8 (Beaufort scale) and significant wave heights of 4 m and above but excluding abnormal conditions, and vessels largely self-sufficient.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.5 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Oceanis 36 CC is about 241 kg/cm, alternatively 1351 lbs/inch.
Meaning: if you load 241 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1351 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Oceanis 36 CC is 2.84.

Compared with other similar sailboats it is more spacy than 86% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.

Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Jib sheet	10.8 m	(35.4 feet)	14 mm	(0.55 inch)
Genoa sheet	10.8 m	(35.4 feet)	14 mm	(0.55 inch)
Mainsheet	27.0 m	(88.6 feet)	14 mm	(0.55 inch)
Spinnaker sheet	23.8 m	(78.0 feet)	14 mm	(0.55 inch)

Boat owner's ideas

This section is reserved boat owner's changes, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Oceanis 36 CC it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.