Review of Impala 28 (Jensen)

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

The interior is like most other boats made of teak. Teak has the advantage of being naturally very oily and therefore water-repellent, which is suitable on boats.
The boat is equipped with 2 cabins, 5 berths, a galley and toilet facility.

The Impala 28 (Jensen) is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a long keel.

The boat can enter most marinas as the draft is just about 1.50 - 1.60 meter (4.92 - 5.22 ft) dependent on the load. See immersion rate below.

Impala 28 (Jensen) is typically equipped with an inboard Bukh diesel engine at 10.0 hp (7 kW), which gives a max speed about 4.1 knots.

The transmission is a shaft drive. A shaft drive will in the long run require less maintenence than other types of drive e.g. a sail drive.

What is Capsize Screening Formula (CSF)?

The capsize screening value for Impala 28 (Jensen) is 1.87, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.1 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Impala 28 (Jensen) is about 117 kg/cm, alternatively 655 lbs/inch.
Meaning: if you load 117 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 655 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Impala 28 (Jensen) is 25.2.

Comparing this ratio with similar sailboats show that it is more comfortable than 69% of all similar sailboat designs. This comfort value is just above average.

What is L/B (Length Beam Ratio)?

The l/b ratio for Impala 28 (Jensen) is 3.16.

Compared with other similar sailboats it is slimmer than 62% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.

What is Displacement Length Ratio?

The DL-ratio for Impala 28 (Jensen) is 340 which categorizes this boat among 'heavy cruisers'.

14% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 20m² (215 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section is reserved boat owner's changes, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

We are always looking for new photos. If you can contribute with photos for Impala 28 (Jensen) it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.