Review of Celere 48

Basic specs.

The Celere 48 is a large sailboat designed by the maritime architect Bryce Fuhriman in the late eighties. The Celere 48 is built by the Chinese yard Celestial Marine Ltd..

Here we would have liked to show you nice photos of the Celere 48.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Celere 48 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Rig

The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Keel

The Celere 48 is equipped with a long keel. A long keel provide a better directional stability than a similar boat with a fin keel; on the other hand, better directional stability means also that the boat is more difficult to handle in a harbour with less space.

The boat can only enter major marinas as the draft is about 1.98 - 2.08 meter (6.50 - 6.80 ft) dependent on the load. See immersion rate below.

Engine

The boat is typically equipped with a Perkins 4.238 diesel engine at 85.0 hp (63 kW), which gives a max speed about 7.7 knots.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Celere 48 is 1.74, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 8.3 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Celere 48 is about 321 kg/cm, alternatively 1801 lbs/inch.
Meaning: if you load 321 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1801 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Celere 48 is 34.9.

Comparing this ratio with similar sailboats show that it is more comfortable than 54% of all similar sailboat designs. This comfort value is just above average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Celere 48 is 3.56.

Compared with other similar sailboats it is slimmer than 62% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Celere 48 is 39%.

This ballast ratio shows a righting moment that is higher than 69% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Celere 48 is 238 which categorizes this boat among 'light crusers & offshore racers'.

46% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.

SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Celere 48 with ISO 8666 reference sail is 17.9, with a 135% genua the SA/D is 20.7.

The SA/D ratio indicates that it is faster than 31% of all similar sailboat designs in light wind.

Over- / underrigged

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 36m² (387 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

Dimensions of sail for masthead rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	47.0 m	(154.3 feet)	14 mm	(0.55 inch)
Jib/genoa halyard	47.0 m	(154.3 feet)	14 mm	(0.55 inch)
Spinnaker halyard	47.0 m	(154.3 feet)	14 mm	(0.55 inch)
Jib sheet	14.6 m	(48.0 feet)	16 mm	(5/8 inch)
Genoa sheet	14.6 m	(48.0 feet)	16 mm	(5/8 inch)
Mainsheet	36.6 m	(120.0 feet)	16 mm	(5/8 inch)
Spinnaker sheet	32.2 m	(105.6 feet)	16 mm	(5/8 inch)
Cunningham	5.9 m	(19.5 feet)	14 mm	(0.55 inch)
Kickingstrap	11.9 m	(39.0 feet)	14 mm	(0.55 inch)
Clew-outhaul	11.9 m	(39.0 feet)	14 mm	(0.55 inch)

Boat owner's ideas

This section is reserved boat owner's changes, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Celere 48 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.