Review of Sceptre 36

Basic specs.

The Sceptre 36 is a sailboat designed by the maritime architect Hein Driehuyzen in the late seventies. The Sceptre 36 is built by the Canadian yard Sceptre Yachts Ltd..

Here we would have liked to show you nice photos of the Sceptre 36.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Sceptre 36 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Rig

The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Sceptre 36 is 1.74, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.2 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Sceptre 36 is about 206 kg/cm, alternatively 1156 lbs/inch.
Meaning: if you load 206 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1156 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Sceptre 36 is 34.4.

Comparing this ratio with similar sailboats show that it is more comfortable than 85% of all similar sailboat designs. This is a comfort value significantly above average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Sceptre 36 is 3.21.

Compared with other similar sailboats it is more spacy than 54% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Sceptre 36 is 327 which categorizes this boat among 'heavy cruisers'.

21% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.

SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Sceptre 36 with ISO 8666 reference sail is 13.9, with a 135% genua the SA/D is 16.8.

The SA/D ratio indicates that it is faster than 15% of all similar sailboat designs in light wind.

Maintenance

Rig

Dimensions of sail for masthead rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	32.9 m	(108.0 feet)	12 mm	(1/2 inch)
Jib/genoa halyard	32.9 m	(108.0 feet)	12 mm	(1/2 inch)
Spinnaker halyard	32.9 m	(108.0 feet)	12 mm	(1/2 inch)
Jib sheet	11.2 m	(36.6 feet)	14 mm	(0.55 inch)
Genoa sheet	11.2 m	(36.6 feet)	14 mm	(0.55 inch)
Mainsheet	27.9 m	(91.5 feet)	14 mm	(0.55 inch)
Spinnaker sheet	24.6 m	(80.6 feet)	14 mm	(0.55 inch)
Cunningham	3.6 m	(11.7 feet)	12 mm	(1/2 inch)
Kickingstrap	7.2 m	(23.5 feet)	12 mm	(1/2 inch)
Clew-outhaul	7.2 m	(23.5 feet)	12 mm	(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's changes, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Sceptre 36 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.